781-273-2773     
info@stevesdepot.com     
 
Digitrax
LocoNet Cabling & Diagnostic
Digitrax cabling products compatible with both Digitrax LocoNet and NCE Cab Bus

These products allow you to make various-length cables for your cab bus.

Because the RJ-12 modular jacks and cabling for Digitrax and NCE are identical, all of these products will work for both Digitrax LocoNet and NCE Cab Bus installations.

Note that diagnostic products such as the LNRP and LT1 are not compatible with NCE systems.

Model Description List Steve's Add Cart
Prefabricated Cables
LNCCMC1 Coiled Cord & RJ12 Modular Adapter (by Digitrax)

Add a coiled cord to your throttle without soldering!

Just plug the modular adapter provided on to your existing throttle plug and add the coiled cord.

16.00 12.79
LNC82 Two 8-foot Cables (by Digitrax)

2 pack of 8-foot Digirax LocoNet/NCE Cab Bus cables.

Convenient pre-made, pre-tested cables, ready to use on your layout.

Digitrax LocoNet and NCE Cab Bus wiring is a snap with these cables.

10.00 7.95
LNC162 Two 16-foot Cables (by Digitrax)

2 pack of 16-foot Digirax LocoNet/NCE Cab Bus cables.

Convenient pre-made, pre-tested cables, ready to use on your layout.

Digitrax LocoNet and NCE Cab Bus wiring is a snap with these cables.

17.00 13.59
LNC501 One 50-foot Cable (by Digitrax)

50-foot Digirax LocoNet/NCE Cab Bus cable.

Convenient pre-made, pre-tested cable, ready to use on your layout.

Use for long runs or divide into custom lengths using Cable Maker Kit & RJ12 Plugs.

25.00 19.95
Custom Cabling Kit & Parts
LNCMK Cable Maker Kit (by Digitrax)

Everything you need to make Digitrax LocoNet or NCE Cab Bus cables for your layout:

  • Crimper tool for cutting cables to length and attaching plugs to cable ends.
  • LT1 LocoNet Tester for testing cables prior to installation on layout.
  • 50-foot Cable - pretested and ready to use as a single long run or to be cut into smaller lengths.
  • 20 RJ12 Plugs for making up cables or for repairing broken plugs on throttles and LocoNet cables.

50.00 39.95
LNMC3 RJ12 Modular Adapter - 3 Pack (by Digitrax)

Use for joining Digitrax LocoNet or NCE Cab Bus cables, adding coiled cords to throttles, etc.

10.00 7.95
LNRJ12P20 RJ12 Plugs - 20 Pack (by Digitrax)

Use with crimper tool to make custom length Digitrax LocoNet or NCE Cab Bus cables & replace broken plugs.

10.00 7.95
Diagnostic
LNRPXTRA LNRP Xtra LocoNet Repeater Module

-- Now includes PS14 power supply! --

The LNRP Xtra LocoNet Repeater Module isolates and protects LocoNet layouts. It allows for greater expansion of the LocoNet system on large installations.

If a wiring or signal problems occur on any "standard" LocoNet section that the LNRP Xtra is connecting and monitoring, the LNRP Xtra will act to internally disconnect the faulty "standard" LocoNet segment so that the "protected" LocoNet can continue operating.

If the fault is removed, the LNRP Xtra will typically automatically reconnect and resume operations on the "standard" LocoNet segment.

Features

  • Isolates segments of your LocoNet layout
  • Protects segments of your LocoNet layouts
  • Extends large LocoNet installations of more than 20 devices
  • Acts as a Diagniostic tool if LocoNet network problems occur
  • FCC Part 15, Class B RFI compliant
  • Includes the PS14 power supply
72.00 57.59
LT1 LT1 Tester for Decoders & LocoNet Cables

The LT1 is included with all Digitrax Starter Sets.

It consists of a harness with 6 conductor Telco type wire with a male plug, a tester with a female 6 conductor jack, and a 100 Ohm 2 watt protection resistor.

Features

  • Use as a diagnostic test light
  • Test decoders prior to installation
  • Test Track power
  • Test LocoNet cables

5.00 4.95